Did you hold the start button for a few seconds after locking it?
WTH is up with my remote start?
2012 Coupe A/T
I read that they come stock with remote start, but mine does not work at all. I had a CEL but turned off those codes with HPTuners thinking that would fix it but it did not. I tried locking the doors once to 3 times, then pushing the start button. Nothing. No lights (except locking the doors), no fuel pump trying to power on. Nothin. Any clues on where to start?
I read that they come stock with remote start, but mine does not work at all. I had a CEL but turned off those codes with HPTuners thinking that would fix it but it did not. I tried locking the doors once to 3 times, then pushing the start button. Nothing. No lights (except locking the doors), no fuel pump trying to power on. Nothin. Any clues on where to start?
- Status
- Not open for further replies.
1 - 15 of 15 Posts
Yup. Nothin. I just went out and tried again.Did you hold the start button for a few seconds after locking it?
Neither fob will do it?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Hood is closed right?
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk
I only have one fob, and hood is closedNeither fob will do it?
Sent from my iPhone using Tapatalk
I think depending on the type of code, if it is not fixed but turned off in HPT, until that specific code is fixed, it will not auto-start. I had a "Rear Access Open" code (BCM related) and my auto-start would not work until I got new BCM and fixed the broken wire in/ on the trunk lid. The broken wire fired the BCM.I only have one fob, and hood is closed
The only codes I have are for the rear O2 sensors
I am not sure but check the fuse box and see if there is a fuse for the auto start. All check all the BCM fuses and make sure they are all good. I think there are about 5 or 6 of them (BCM). It will be the fuse box in the engine bay.The only codes I have are for the rear O2 sensors
I thought that after my o2 sensor codes were fixed that I would be able to do it, but nope. I WAS able to get the lights to flash after I hit the lock button 2 times and held the start button but it didn’t try to start. It’s really eating at me that this isn’t working.
Check all the BCM fuses.I thought that after my o2 sensor codes were fixed that I would be able to do it, but nope. I WAS able to get the lights to flash after I hit the lock button 2 times and held the start button but it didn’t try to start. It’s really eating at me that this isn’t working.
All BCM fuses checked fine.
Full tank of gas. I verified with my GM pass-thru that there are no codes.
-hood is closed
-no codes (not even in history)
-no TPMS codes
-New remote battery
-full tank
-battery in car is good
-fuses are good
-wiring is good
- doing correct method to start it
it’s almost like it’s not programmed to do it???
The only “error” I have is the AFL is disabled because of my aftermarket headlights but that’s all
Got it!! Cleared the codes with GM TLC and it works! I guess the diablo, HPT, and Snapon passthru software were not clearing it.
-hood is closed
-no codes (not even in history)
-no TPMS codes
-New remote battery
-full tank
-battery in car is good
-fuses are good
-wiring is good
- doing correct method to start it
it’s almost like it’s not programmed to do it???
The only “error” I have is the AFL is disabled because of my aftermarket headlights but that’s all
Got it!! Cleared the codes with GM TLC and it works! I guess the diablo, HPT, and Snapon passthru software were not clearing it.
Still working flawlessly. I even got my new remote programmed! That was hella easy to do!
1 - 15 of 15 Posts
- Status
- Not open for further replies.
Cadillac CTS-V Forum
A forum community dedicated to Cadillac CTS-V owners and enthusiasts. Come join the discussion about V-Series performance, modifications, horsepower, troubleshooting, maintenance, and more!
Full Forum Listing
Recommended Communities
