New to the forum

724 Views 11 Replies 6 Participants Last post by PGA2B, 2 mo ago

Chokeu

Discussion Starter · 2 mo ago

Thanks for the add. Just sold my 06 Corvette as the miles were getting a little high and picked up a 2013 Crystal Red V sedan with 58k on the clock. First time owning a CTS-V even though I’ve been wanting one for the past few years. Car came with Texas Speed LT headers and 3” X-pipe (no cats), Corsa Sports, New Era CAI and a tune (no idea who). Any advice what mods I should do first?

Save

1 - 12 of 12 Posts

Rekkr

· #2 · 2 mo ago

Welcome to the forum. Post up pics of the car when you can. I’d get some cooling mods on the list then do injectors and pulley. It’ll really wake the car up

Save

Reactions: 1

Chokeu

Discussion Starter · #3 · 2 mo ago

I noticed you have a ZL-1 lid on your car, does it require milling to make it fit? Also does it clear the strut tower brace?

Some pics

See less See more

Save

Reactions: 1

Rekkr

· #4 · 2 mo ago

Don’t quote me on this but I think either needs to be milled or you can lower the cradle? Someone else will chime in I’m sure.
Mine clears the strut bar no problem

Save

SaskV

· #5 · 2 mo ago

The ZL1 lid clears the V2 strut brace without an issue, however the lid requires milling otherwise it will contact the hood near the front of the lid.

Here's a couple of photos of my lid pre and post milling respectively;

Gas Composite material Auto part Musical instrument accessory Metal

Black Grille Gas Automotive exterior Rectangle

Lots of room under the tower brace, not so much between the lid and hood

Vehicle Hood Car Automotive lighting Automotive design

See less See more

Save

Reactions: 1

Chokeu

Discussion Starter · #6 · 2 mo ago

I noticed on DSX Tuning's website that they sell a ZL-1 lid and it gives the option of milling it or not, that's why I asked. Some people have told me that they didn't mill theirs while others said they did? Another question is what exactly do they do to the brick to reinforce it? Sorry for the dumb questions, I'm new to this platform.

Save

mememe123

· #7 · 2 mo ago

Chokeu said:
I noticed on DSX Tuning's website that they sell a ZL-1 lid and it gives the option of milling it or not, that's why I asked. Some people have told me that they didn't mill theirs while others said they did? Another question is what exactly do they do to the brick to reinforce it? Sorry for the dumb questions, I'm new to this platform.

They weld extra plates on the sides to reinforce it. Just be carefully in the future if you up the boost, it will start leaking. I think there are a couple people on here to incoude me, that had that happen after about a year. C&R brick is a far better upgrade in my opinion.

Save

Reactions: 1

Chokeu

Discussion Starter · #8 · 2 mo ago

Thank you, that’s good to know. Damn, that C&R brick isn’t cheap.

Save

SaskV

· #9 · 2 mo ago

Chokeu said:
Thank you, that’s good to know. Damn, that C&R brick isn’t cheap.

Actually there was a cost decrease by about $300 on the C&R brick for 2023. 😉

Save

Reactions: 1

Chokeu

Discussion Starter · #10 · 2 mo ago

Is C&R the only company that sells a heavy duty brick?

Save

Lt1z

· #11 · 2 mo ago

Chokeu said:
Is C&R the only company that sells a heavy duty brick?

Yes AFAIK.

Don’t think they have gotten to the point if Aliexpress knock offs yet.

Save

Reactions: 3

PGA2B

· #12 · 2 mo ago

Lt1z said:
Don’t think they have gotten to the point if Aliexpress knock offs yet.

Nor would I trust one even if they did exist.

Save

Reactions: 1

1 - 12 of 12 Posts

New to the forum

Chokeu

Rekkr

Chokeu

Attachments

Rekkr

SaskV

Chokeu

mememe123

Chokeu

SaskV

Chokeu

Lt1z

PGA2B

Top Contributors this Month